Interface Range Command Configuration Ip With Ease
Result for: Interface Range Command Configuration Ip With Ease
Sep 4, 2020 The Interface Range Specification feature makes configuration simpler and quicker because Same commands can be entered at once for a range of interfaces, rather than being entering separately for each interface. Interface ranges can be saved as macros; A continuous set of interfaces can be included in range command by using hyphen (-).
Oct 7, 2009 Configuring a Range of Interfaces . To configure a range of interfaces, perform this task: SUMMARY STEPS . 1. enable. 2. configure terminal. 3. interface range {macro macro_name} 4. interface range {vlan vlan_ID - vlan_ID} [, {vlan vlan_ID - vlan_ID}...] 5.
The interface range Command. If you have multiple interfaces that need to be configured with the same settings, you can use the interface range command to specify a range of interfaces to which the subsequent commands will be applied.
Router(config)# interface range fastethernet 5/1 - 5, gigabitethernet 1/1 - 2 Selects the range of interfaces to be configured. The space before the dash is required. For example, the command interface range gigabitethernet 1 - 5 is valid; the command interface range gigabitethernet 1-5 is not valid. Step 6 end Example: Router(config-if)# end
Feb 11, 2009 The switchport numbering may not always be the same depending on the platforms. You should also consider other type of interfaces such as; Ethernet, GigaEthernet and TenGigaEthernet. if i have to select ports from fa0/1-24, how can i use the "interface range" to select this range? interface range fa0/1-24. HTH, __ Edison.
The format of the interface range command is as follows: range should be specified with - (hyphen). interface range command. (config)#interface range
/ (config-if-range)# To configure multiple non-contiguous interfaces at once, delimit them with a comma (,).To configure an interface range, use the interface-range statement at the [edit interfaces] hierarchy level. The interface-range statement accepts only physical networking interface names in its definition. Junos OS supports interface ranges for the following interface types:
Note When you use the interface range command, you must add a space between the vlan, fastethernet gigabitethernet, tengigabitethernet, or macro keyword and the dash. For example, the command interface range fastethernet 5/1 - 5 specifies a valid range; the command interface range fastethernet 5/1-5 does not contain a valid range command ...
The bottom of the configuration in Example 1 shows a way to shorten your configuration work when making the same setting on multiple consecutive interfaces. To do so, use the interface range command. In the example, the interface range FastEthernet 0/11 - 20 command tells IOS that the next subcommand(s) apply to interfaces Fa0/11 through Fa0/20.
Step 1 Step 2. Step 3. Step 4 Step 5 Step 6. Enter global configuration mode. Enter interface range configuration mode by entering the range of interfaces (VLANs or physical ports) to be configured. You can use the interface range command to configure up to five port ranges or a previously defined macro.
you exit interface range configuration mode while the commands are being executed, some commands might not be executed on some interfaces in the range. Wait until the command prompt reappears before exiting interface range configuration mode. The interface range command works only with VLAN interfaces that have been created with the interface
Aug 19, 2022 The command can be used in following Interface types . Ethernet interface. Management interface. Sub interfaces. Virtual Ethernet interface. Cisco Device Interface Description Configuration Example. Below is the configuration example where Interface Description is used on Interface Fa0/0 of Router R1 . R1 (config) interface Fa0/0.
Apr 25, 2018 Command. Interface Range. Use. This is the modern way to configure VLANs. A useful feature is that you can configure a range of VLANs with a single command. Syntax. Switch(config)#interface range Options < >
All configuration changes made to a range of subinterfaces are saved to NVRAM, but the range itself does not get saved to NVRAM. Use the define interface-range command to create and save a range. When you define a VLAN range, valid values are from 1 to 4095. The last VLAN number cannot exceed 4095.
Use interface range to create an interface range and enter the interface range view.. Syntax. interface range interface-list. Views. System view. Predefined user roles. network-admin. Parameters. interface-list: Specifies a space-separated list of up to 24 interface items.Each item specifies an interface by its type and number or a range of interfaces in the form of interface-type interface ...
Feb 27, 2021 Function. The interface range command creates a temporary interface group and adds specified interfaces to this temporary interface group. Commands configured for a temporary interface group then automatically run on all member interfaces. By default, no temporary interface group is created. Format.
Use this command to bulk configure multiple interfaces with the same feature instead of configuring them one by one. For example, execute the shutdown command in interface range view to shut down a range of interfaces. The interface range created by using this command is not saved to the running configuration. You cannot use the interface range ...
The following command configures a range of interface as a trunk port for a set of VLANs: (host) [00:0b:86:99:88:17] (config) #interface range gigabitethernet 0/0/0-0/17. (host) [00:0b:86:99:88:17] (config-submode)#switchport mode trunk. (host) [00:0b:86:99:88:17] (config-submode)#switchport trunk native vlan 10.
Interface Configuration Mode. Breakout Interfaces. Default Ethernet Interface Configuration. Interface Speed and Duplex Mode. Speed and Duplex Configuration Guidelines. IEEE 802.3x Flow Control. Layer 3 Interfaces. Interface Types. This section describes the different types of interfaces supported by the device.
Use this command to enter interface range view to bulk configure multiple interfaces with the same feature instead of configuring them one by one. For example, run the shutdown command in interface range view to shut down a range of interfaces. In interface range view, only the commands supported by the first interface are available.
define interface-range macro-name interface-range Syntax Description Command Default This command has no default settings. Command Modes Global configuration (config) Command History Usage Guidelines The macro name is a 32-character maximum character string. A macro can contain up to five ranges. An interface range cannot span slots. When ...
Dec 1, 2023 Configuration Guides. Interface and Hardware Component Configuration Guide for Cisco 8000 Series Routers, IOS XR Release 7.11.x. Download. Updated: December 1, 2023. Chapter: IP Event Dampening. Chapter Contents.
Related Keywords For Interface Range Command Configuration Ip With Ease